Installation steps for ultra-thin advertising light boxes? do you know?

Ultra-thin light box is a widely used advertising light box. It has beautiful appearance, ultra-thin and ultra-light, light box use and long life. It is often used in elevators, public passages, shopping malls, supermarkets, airports, subways, stations and other places. 


There are many types of advertising light boxes, in fact, their installation methods are similar. Today, we will discuss the installation method of ultra-thin light boxes and see what the installation steps of ultra-thin advertising light boxes are.



The first step is to determine the installation position of the light box


Since the installation position of the light box determines the later effect of the light box, the choice of the position of the light box is very important. This requires the installer to determine the installation position according to the customer's requirements and the actual situation on site to ensure that the ultra-thin light box is installed in the accurate position.


The second step is to determine the fixed point for installing the light box


Generally speaking, there are mounting holes on the back of the light box. We can determine the fixed point for installing the light box according to its position or the size of the site.


The third step is to fix the light box


Fixing methods can be divided into four types according to the actual situation:


1. If the wall to be installed is aluminum-plastic board, wood board, iron board, etc., it can be fixed directly with screws;


2. If the wall to be installed is a cement or brick wall, it can be drilled with an impact drill first, and then fixed with expansion screws;


3. If the wall is made of tiles, marble, glass, etc., you can first drill through the surface with a glass drill bit, then drill the expansion screw holes, and then fix the ultra-thin light box or use glue;


4. If it is a hoisting or hanging light box, after selecting the installation location, it is necessary to determine the fixing point of the light box according to the actual size of the installation hole of the light box, and then install the hanger and connect the ground wire.


The fourth step, ultra-thin light box wiring.


When wiring the light box, generally choose the standard for getting electricity nearby. A power socket can be installed near the outlet of the power cord behind the light box, so as to facilitate the control of the power supply of the light box in the future. Of course, there is another way to directly remove the plug of the power cord and use the direct wiring method, but when you need to pay attention, when using this method, you must wrap the connector tightly with insulating tape. .


The fifth step is to fix the light box from the inside.


Open the top cover of the light box and install it in alignment with the fixed point, that is, use an electric drill to drill holes at the position of the power cord at the base of the light box, re-install the power cord, and adjust it to a horizontal state with a spirit level.


The sixth step, turn on the power.


Test whether the various properties of the ultra-thin light box are normal, and finally cover the upper cover of the light box and clean the surface of the light box.


The installation of the ultra-thin light box determines the quality of the light box and the quality of advertising in the future, so we must install the ultra-thin light box in the correct way in accordance with the specifications. This can not only bring better advertising effects, but also appropriately extend the service life of the advertising light box.


Kingwe-Star is a professional led light box manufacturer in China, specialising in high-quality ultra-thin light box and advertising light boxes wholesale for years, welcome to contact us!

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more