What are the symptoms of a broken car ignition coil?

The ignition system of a car does not mean that the ignition of the spark plug will start the vehicle, but in fact, the ignition of the spark plug cannot be done by itself. Among them, the auto ignition coil of the car plays a key role and is connected to the spark plug. The primary coil is charged by the battery, and the secondary coil is discharged to the spark plug.


First, the role of the car engine coil

The core components of the ignition device are the auto ignition coil and the switch device, which are manually controlled by us, and the ignition coil is an internal part, which is connected with the spark plug to increase the energy of the engine coil, and the spark plug can generate enough energy. The main coil of the ignition coil is charged by the battery, the secondary coil is discharged to the spark plug to complete the ignition, and the triode is responsible for switching.


Symptoms of a broken auto ignition coil

1. If the engine coil of the car is broken, when idling, the engine of the car will keep shaking, the cylinder is missing, and you can hear the sound of "chug".


2. If the vehicle speed is below 2500 while driving in China, the body shakes obviously, the acceleration is weak, and if the vehicle speed is above 2500, the feeling of shaking disappears, which is also the problem of the ignition coil.


3. Open the engine cover and observe the running engine. If there is obvious jitter, it is no longer the jitter under normal working conditions, and the jitter amplitude is relatively large, which is likely to be a fault of the engine coil.


3. Reasons for the damage to the auto ignition coil

1. If it is used for too long, the insulating layer will age, which usually happens in old cars. If the service life is not long, the engine coil insulation needs to be checked for the rapid deterioration of the ignition coil insulation due to excessive spark plug gap load and heat.


2. When the engine is overheated, the insulating paint of the ignition coil is baked, which means that the gap between the electrodes of the spark plug will be too large, thereby increasing the load of the engine coil, and the breakdown of the high-voltage coil will cause a short circuit.


3. The plug of the auto ignition coil may also be loose. If the plug comes loose, the additional resistance of the auto ignition coil



will inevitably be damaged.


4. The most common is self-destruction. When the engine coil ruptures, electricity leaks, resulting in insufficient ignition capacity.


If only one engine coil fails, the other three cylinders work fine and are barely drivable, but will adversely affect the engine, engine mounts and connecting components. If this happens, it is recommended not to continue driving, especially if the auto ignition coil of more than one cylinder is burned out, stop immediately, otherwise, it will cause irreparable damage.


Haiyan is a professional Ignition Coil Manufacturer in China, focusing on high-quality Engine Coil and Auto Ignition Coil manufacturing, welcome to contact us!

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more