When testing textile formaldehyde content, what should pay attention to

There are three main points for attention in the formaldehyde content test of textiles:

 

1. Selection of sample test quantity

2. Sample storage

3. Color rendering

 

Details of textile testing precautions:

 

1. Selection of the number of samples tested

If the formaldehyde content in the sample is too low, the number of samples should be increased from 1g to 2.5g to ensure the accuracy of the test results. This method complies with the provisions of GB/T2912.1 "Determination of Formaldehyde in Textiles Part 1: Free Hydrolyzed Formaldehyde (Water Extraction Method)".

 

Using different sample quantities and using the same test method will lead to different conclusions. Because according to GB/T2912.1 "Determination of Formaldehyde in Textiles Part 1: Free Hydrolyzed Formaldehyde (Water Extraction)", the measurement range is between 20-3500mg/kg, considering that the formaldehyde content is too low The linear relationship between absorbance and formaldehyde content may deviate from the factor of Beer's law, and the test conclusion of selecting a 2.5g sample is reasonable.


2. Sealing of samples

In the process of taking representative samples, the samples should be sealed up in a timely manner, otherwise the accuracy of the test results will be affected.

 

Samples should be randomly selected from each batch of products and sealed immediately, otherwise the test data will drop due to the volatilization of formaldehyde, which will affect the representativeness of the determination of formaldehyde content.

 

3. Color rendering

It is advisable to suck the extract into the test tube before the acetylacetone (Nessler's reagent) to prevent the oily acetylacetone from adhering to the test tube wall and affecting the absorbance reading.

 

The validity period of acetylacetone and the preparation process have an impact on the formaldehyde test, so strict management must be carried out to ensure that it is used within the validity period.

 

It should be noted that after completing the preparation of the acetylacetone reagent, it must be stored for 12 hours before use, otherwise it will affect the accuracy of the test. This is because the chemical properties of the Nessler reagent used for color development just after the preparation is completed It is not stable enough, and it usually takes 12 hours to reach stability. The glass bottles used for storage should be brown to prevent chemical reactions between light and reagents and affect the color rendering effect.

 

The test of formaldehyde content is a test with relatively high operational and technical requirements. There are also: calibration of the formaldehyde stock solution before the test, determination of the standard curve, control of the temperature and time during extraction of the extract, selection of spectrophotometer and colorimetry Matching selection of dishes; etc. These factors will have a direct impact on the test results, so necessary attention must be paid to improve the accuracy of the test results.


Gester instruments is a global leading textile testing instruments manufacturer with 20+ years experience.Expertly specialized in providing integrated laboratory testing solutions for children's products, textile, footwear and furniture. It has passed ISO 9001 certificate, "AAA Enterprise in Quality, Service and Credit" and was audited as SGS audited supplier.So far, GESTER owns two production factories and four sales teams for textile tester, footwear tester, Mask Tester and Protective Clothing Tester, Lab Incubator, Biological Safety Cabinet, Lab Oven etc. We have applied for dozens of patents from the State Intellectual Property Office.More about textile testing machines pls leave message to us,we will contact you by 24 hourse!

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more