Its application areas will be determined by the characteristics of melt-blown filter elements

These four advantages of melt-blown filter elements can be divided into four parts.


1.You should use polypropylene raw material. Then, wind continuous polypropylene long fibres made by melt-blown technology.


2.The second is that the filtration accuracy, flow rate, structure, dirt holding capacity, and service life are all high.


3.It is also chemically compatible without adding any additives. Third, the fiber is very hard to lose.


4.It is also widely used.


High dirt retention capacity:


1.To maximize the effectiveness of the filter element's filtering ability, it is important to understand the effects of capturing particles according the density classification in its deep layer.


2.A higher dirt retention capacity can mean a longer service life, lower replacement frequency, and cost savings.


3.The filter element's surface density is low and gradually increases in density from the center to the surface.


4.There are no blind spots that could reduce the flow rate or increase frequency of replacement.


5.The polypropylene structure in the melt-blown filter element is:


6.High temperature bonding fiber. Does not contain antistatic agents, humectants or binders. It has a broad range of chemical resistance and is easy to handle after incineration.


7.Application areas of melt-blown filter element


8.Pre-filtration of various injectables, medical solutions, and injection bottle wash water for the pharmaceutical industry.


9.Food industry: Filtration of alcohol, beverages, and drinking water.


10.Pre-filtration of purified water and ultra-pure waters for the electronics industry


11.Petroleum and chemical industry: Filtration of various organic solvents, acids, and lyes. Also, oilfield water injection filtering.


Guangzhou Lvyuan Water Purification Equipment Co., Ltd. specializes in the production of filter elements, welcome to consult!

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more