How to produce high flow water filter or pleated filter cartridge ?

1. Filter paper machine to produce filter cartridges pleats.


Putting quality tested filtration media with suitable width on a roller, pleating machine starts making some plates as trial running to adjust pleating speed and pleating height. Pleated design increased the filtration area for deep filtration.


The cutter of the pleating machine set to cut off a certain length of pleated membrane. One worker will gather the pleated membrane into a box and forward to the next procedure. This type of water filter cartridges is available in a wide range of chemical compatibility.


2. Side Seam Thermal Welding


Cutting off cartridge filters the pleats to suit for filter cage.


We need to cut off the surplus length on both sides of the thermal welded pleated membrane to make sure it is 20/40/60 inches long to fit the cage and end caps. Length control is important for the filter cartridge integrity. Too long which will affect the flow rate or too short which cause leakage in the filtration process. 


Middle seam welder to do seam thermal welding of filter cartridge paper 


Ultrasonic thermal welding is a high technology for side seam sealing of membrane pleated, without any additives & glues in the process which making sure 100% integrity of the side seam and not any pollution. Keeping clean and stable for the membrane pleated cartridge filters and high flow pleated filter cartridge in the filtration process. 


3. Cartridge shape 


Putting the correct length pleated membrane which contains an inner core inside into the outer cage. Assembled Semi-finished filters which placed neatly to clean and tidy box, waiting for the next step.


4. End caps for welding 


To welding Flat cap onto both ends of the filter cartridge, which makes pleated membrane, inner core & outer cage together as 100% integrity.  


5. Fitting end caps and filter cartridge length connecting welding


Fitting end cap


Putting the end caps on both ends and the filter cartridge in the middle of end caps thermal welding machine. 


Setting suitable temperature, Two end caps which could be fin, 222, 215, 226 moves forward to the middle and get in touch with a flat cover. 


A few seconds later, end caps, pleated membrane and outer cage & inner cage are thermal welded together to form a complete pleated filter cartridge. 


Length connecting


Welding 2/3 pieces together to complete 40/60 inches long high flow pleated filter cartridge, so that all the part of the pleated filter cartridge is thermal welded together, complete the production of membrane pleated cartridge filter.


Guangzhou Lvyuan Water Purification Equipment Co., Ltd. specializes in the production of various filter elements, welcome to consult

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more