How does the car ignition coil work?

The main cause of car ignition coil burnout is the aging and breakdown of the insulation layer or the damage of the switching transistor. The spark plug gap will cause the main coil to load, heat, and the insulation layer will age quickly. The small spark plug gap will cause the secondary coil to discharge current, heat, and the insulation layer. Fast, the assembled car ignition coil may have a shorter lifespan, such as poor durability of insulation materials, large internal resistance of the coil, high heat generation, and low quality of the tertiary tube.


If it is always burned out, and it will burn out soon after replacement, what is the reason? The following summarizes some:


1. First look at the problem of the generator. If the power generation is too high, the car ignition coil will burn out if the load is too heavy, but if the power generation is really too high, then the body electrical appliances, such as light bulbs, will often be damaged; of course The quality of the accessories is not ruled out, so it is best to measure the power generation first.


2. The spark plug gap is too large, adjust the gap or replace the spark plug;


3. The quality of gasoline is not good, try changing to higher-grade gasoline;


4. The cylinder compression ratio is wrong, adjust the compression ratio;


5. If there is a program failure on the computer board, you can go to the repair shop to test the car with a computer and clear the error message. If it still doesn't work, there may be a problem with your car's transmission.


6. The power supply voltage is unstable;


7. The resistance of the high-voltage line is abnormal, replace the high-voltage line;


8. There is a short circuit phenomenon in the secondary;


9. The primary current of the ignition controller is too high, which causes the car ignition coil to overheat;


10. It is not good to work due to problems with high temperature and high pressure waves;


11. It is very unlikely that the coil itself is a problem, you can try another brand;


12. The integrated block of the igniter does not work well;


The car ignition coil itself is a transformer, which is like a transformer in a household appliance. When the voltage changes within the specified range, the transformer will not be burned. Normally, the burning of the transformer will only cause this situation when the transformer is overloaded. When solving this problem, we must try to find out the cause of the excessive load or the aging of the components.


Haiyan is a mature ignition coil manufacturer and supplier, specialized in car ignition coil since 1983, welcome to contact us!

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more