Factors that affect the performance characteristics of PP Cotton Melt Blown Filter Elements

Water quality requirements for PP Cotton Melt Blown Filter Elements are extremely strict. This may be due to their main performance characteristics. We can only control water quality by knowing the performance of the PP Cotton melt blown filter element.


The principal performance characteristics of PP cotton melt blown filters element:


The PP cotton filter element plays a major role in pre-purification of the equipment. It is generally made from polypropylene and is a precision consumable. After the first use, it must be replaced. It takes approximately 1 year to replace it. You should also consider the water quality in your area when determining the replacement time.

Its primary function is to eliminate impurities, bacteria and viruses from water that is larger than 5 microns.


You must use the filter element correctly according to its instructions to avoid damaging it. This will result in a water purifier that is not usable or water quality that is below the standards.


For influent water quality, the main requirements for PP cotton filter elements are:

A pressure reducing valve should be installed in front the water purifier if the inlet water pressure exceeds the recommended level. A booster pump is required if the inlet water pressure drops too low.


The PP cotton filter element has specific requirements regarding the water temperature. Inlet water should be normal-temperature tap water and not hot water. Before installing a heating device, such as a boiler or water heater, install a water purifier.


To prevent steam from the boiler from entering the water purifier, the installation position should be lower than that of the boiler.


Guangzhou Lvyuan Water Purification Equipment Co., Ltd. specializes in the production of various filter elements. Welcome to come and buy!

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more