Brief introduction to the structure of car ignition coil

The car ignition coil is mainly composed of iron core, winding, bakelite cover, porcelain cup, etc.;


(1) The iron core is made of laminated silicon steel strips that are insulated from each other. The sheets are separated by an oil oxide layer or coated insulating group, and the outer layer is covered with an insulating sleeve, whose function is to enhance the magnetic flux.


(2) For the primary winding, an enameled wire with a wire diameter of 0.5 to 1.0 mm is wound on the outer layer of the primary winding in layers to facilitate heat dissipation. The primary winding has 230 to 370 turns. There are also several layers of insulating paper on the outside to enhance insulation. After the winding is wound, it is immersed in a mixture of paraffin wax and rosin in a vacuum to further strengthen the insulation. The function of the primary winding is to use the current change in the winding to achieve electromagnetic induction.


(3) The enameled wire with a wire diameter of 0.06～0.10mm for the secondary winding is wound on the outside of the iron core insulating sleeve, with about 11,000-26,000 turns. In order to strengthen insulation and avoid mechanical damage, each layer of wire is separated by insulating paper, the outermost layer of insulating paper is more, or it is covered with a cardboard sleeve. Its role is to generate a mutual induction electromotive force.


(4) A magnetic steel sleeve is installed between the steel sleeve primary winding and the outer shell. The magnetic steel sheet is rolled into a cylindrical shape to form a part of the magnetic circuit, so that the iron core forms a semi-closed magnetic circuit to reduce magnetic leakage.


(5) The filler is to strengthen insulation and prevent moisture penetration. Fill the shell with asphalt or transformer oil. When the transformer oil is filled, the coil has better heat dissipation, lower temperature rise, and good insulation. In recent years, gas insulation such as sulfur hexafluoride (SF6) or plastic modeling is also used for insulation.


(6) Additional resistor Three-connection type ignition wire post shell is equipped with an additional resistor outside of the shell. Both ends of the additional resistor are connected to the "+ switch" and "switch" posts on the bakelite cover. Its function is to improve the ignition performance. There is no additional resistance for the car ignition coil of the two poles. Connect an additional resistance wire between the ignition switch and the car ignition coil "+" pole


Haiyan is a mature car ignition coil manufacturer and supplier, specialized in car ignition coil since 1983, welcome to contact us!

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more