How do you test the integrity and performance of your water filter element?

For the integrity of the water filter, this feature is very important. So, how is the integrity of the water filter element tested? What is its testing process?


1. The integrity test of the filter element is an experiment used to detect the diffusion flow, bubble point and other parameters of the filter element. The experiment has the advantages of convenient detection and good reliability.


The hydrophilic membrane filter element is tested with pure water, and the hydrophobic membrane filter element is tested with 60% IPA.


Before using the automatic integrity tester, please confirm the accuracy of the integrity tester, check the airtightness of the filter, and check whether the inlet pressure meets the requirements (requires the inlet pressure to be set at 0.5-0.7Mpa), test The temperature is set to 20-25degC.


Wetting process:


1. Close the valve; open the valve and the exhaust valve, open the water pump, the regulating valve, and close the exhaust valve after the water is discharged from the exhaust valve, and start to rinse and moisten the filter element.


2. Fully open the valve, quickly flush for 5 to 10 seconds, adjust valve 4, control the pressure gauge 1 to display about P1=0.40-0.45Mpa, and according to the flow rate of more than 5L/min per 10 inches, rinse the wet filter element for more than 10 minutes ;


The greater the flow rate and the longer the flushing time, the easier it is to wet the filter element, and the more accurate the test result will be.


Advantages: 1. Make the filter element easier and more completely wet to ensure the accuracy of the bubble point test; 2. It can ensure the cleanliness of the filter element.


The process of water filter integrity test:


Turn off the water pump, close the valve, open the valve, connect the machine air pipe to the instrument connection port, and then open the valve to test the machine. It is recommended that customers test the diffusion flow data first, and then the bubbling point data.


Guangzhou Lvyuan Water Purification Equipment Co., Ltd. specializes in the production of various filter elements, welcome to consult!

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more