Before the folding filter element leaves factory, what should you pay attention to?

The fine water filter element, the pleated filter element, is of high hygiene standards. There are many things that must be inspected and tested before it leaves the factory. This method ensures the highest quality foldable filter elements and gives customers greater peace of mind.


The pleated filter element, which is part of the filter element, is a finer water filter. It is a high-hygienic, sterile filter element. Its application is quite broad, so it is important to stop the integrity testing before leaving the factory.


It is important to conduct a goodness test on factory-folded filter elements to make sure that they can meet customer application requirements.


The integrity test of the pleated filter elements is an experiment that detects the bubble point, diffusion flow and other parameters. This experiment offers the benefits of easy detection and high reliability. The hydrophilic membrane filter element of the experiment is tested using pure water and the hydrophobic membrane filtr element with 60% IPA.


Before you use the automatic integrity tester, confirm its accuracy, inspect the air tightness and verify that the inlet pressure is sufficient to reach the requested level. The inlet pressure requested is typically set at 5-7bar and the test temperature to 20-25degC.


Components: Filter, pressure gauge, combined joints, clean air source and liquid pump. The connection is completed by the wet process.


Turn off the valve, close the valve, close the exhaust valve, turn the water pump on, turn on other exhaust valves, then turn on the water pump. Close the exhaust valve and turn off the water pump.


After opening the valve completely, flush it for 5-10 seconds. Adjust the valve and adjust the pressure gauge 1. The pressure gauge 1 should be at P1=4-4.45bar. If the flow rate is greater than 5L/min for 10 seconds, flush out the wet filter element.


The higher the flow rate, and the longer the flushing period, the easier it will be to wet the filter elements, and the more accurate your test results.


Guangzhou Lvyuan Water Purification Equipment Co., Ltd. specializes in the production of various filter elements, welcome to consult!

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more