Ultrasonic flowmeter principle

Many friends will now use ultrasonic flow meters, but many friends do not understand the principle of ultrasonic flow gauges before use, and I will introduce the principle of ultrasonic flow meter.


Level gauge is the most important sensor in traffic monitoring, which has a wide range of applications in sewage treatment, printing and dyeing and municipal water supply. However, a general flowmeter needs to be installed in a separate operating conditions, which is not easy to achieve under some working conditions, so today's protagonist-ultrasonic flowmeter should be born.


The ultrasonic flowmeter entered the domestic market, and was earliered by Dalian Sonyka Co.


Like the ultrasonic flowmeter, the electromagnetic flowmeter, it belongs to the unobstructed flow meter, which is suitable for traffic monitoring of most pure liquid, because it does not have to be broken, and the measurement is simple, it has become a solution to a large class of traffic monitoring. Strategies, especially in terms of large caliber flow measurement.


Ultrasonic flow meters are mainly divided into handheld, outer clamps and wall-mounted ultrasonic flow meters. The most important advantage of ultrasonic flowmeter is portable, easy to carry, and is convenient to install, and the range of traffic detection is also large, and the flow rate of multiple pipe calibers can be detected, not like a pipeline flowmeter, only limit The flow of a caliber is measured. It is necessary to accompany the shortcomings, the maximum disadvantage of the ultrasonic flowmeter is not as high as the accuracy of the pipeline flowmeter. However, the stable flow of fluid helps to measure stability, thereby ensuring measurement accuracy. The fluid in which the flow state confusion makes the measurement data instably or cannot be measured. When the tube greater than DN300 is measured, it is necessary to select an extended bracket. The pipeline diameter using an extended bracket measurement is not less than DN700. The extended bracket can be installed with V method and the Z method, generally recommending the Z method for installation, so signal strength is more.


The installation of the outer clamp sensor has V method and Z method.


DN15MM-200mm pipeline prioritizes V method, two sensors horizontally aligned in installation, in which the centerline is parallel to the pipe axis, and pay attention to the transmission direction to be opposite (two sensor directions). The V method has the characteristics of easy use and accurate measurement. For pipeline installation accuracy of less than DN50mm, please pay attention to signal strength, signal quality, and transmission time than these parameters.


DN200MM-6000mm pipeline prioritization Z method, the Z method can also be selected when the signal or signal quality is not detected in V method. When installing, the vertical distance between the two sensors along the direction of the pipe is equal to the mounting distance, and ensures that the two sensors can be on the same shaft surface, and pay attention to the transmission direction to be opposed (two sensor directions). Since the Z method is the direct delivery of ultrasonic waves in the medium propagation, the signal is not reflected, so the signal strength is attenuated. Therefore, the Z method has a higher signal strength, suitable for ultrasonic signal attenuating a large diameter, impurities or bubbles and fouling of pipelines.

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more