How to accurately measure steam flow

When talking about the flow rate of steam, most of the steam in the market has trade relations. There must be interest controversies for trade relations. How to accurately measure the flow of the instrument? Let's discuss vortex flow meters.

 

In order to accurately measure steam flow, it is inseparable from the selection and installation of the steam flowmeter.

 

The components of the vortex flowmeter have the following four parts: 1. Sensor of flow meter; 2. Pressure transmitter; 3. thermal resistance; 4. Acupillator. Select these four parts according to the actual measured steam data. After selecting the above parts, they must be placed in the scene.

 

It is also important to note that do not exceed the maximum upper and lower limits of the instrument flow range when measuring steam. It is recommended to control the flow rate of the vortex flowmeter between 1/2 and 2/3.

 

It can be seen from the above, the most important thing we emphasizes is to select and install the mass flow meter in the early stage. In fact, different media have corresponding flow meter measure flow. The key is to select and install to effectively save costs and increase profits.


What should I do if the vortex flowmeter does not display flow?


1. Confirm that it is connected, check whether the output voltage of the power board is normal, or try to replace the entire power board to determine it is good.

 

2. Check that the cable is intact and the connection is correct.

 

3. Check the direction of steam flow and whether liquid in the tube is full. For forward and reverse measurements, if the direction is inconsistent, it can be measured, but the set display flow does not match the positive direction and negative direction, and the correction must be performed. If the workload is large, you can also change the direction of the arrow on the sensor and reset the display meter symbol. If the pipe is not filled with liquid, it is mainly due to improper installation of the vortex flowmeter. Measures should be taken during the installation process to avoid that the liquid in the pipe cannot be satisfactory.

 

4. Check that the electrodes on the inner wall of the transmitter covers a liquid housing layer. For measurement steam that is easy to scar, it should be cleaned regularly.

 

5. If it is determined that the converter component is corrupt, replace it.

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more