Should the china sports bra be tight-fitting or should it be bigger?

 We have talked about sports BRA more than once, it can play a very good role in fixing the chest during exercise. Now that it is fixed for use, many girls naturally define it as a "tight" team. But in fact, you might wear the wrong one all the time!


    Fitness experts conducted a test in a sportswear store in New York, USA, and concluded that in order to achieve sufficient support and give a certain comfortable space to the chest during exercise, the best strap for a sports bra should be 5 cm Left and right, the cup should be slightly larger than the normal size.


 

    So in addition, what other aspects should we pay attention to when choosing china sports bra?


    1. Choose chemical fiber fabrics carefully


    You sweat a lot during exercise, and there will be more friction between your body and your underwear. Underwear made of chemical fiber fabrics can easily damage your skin, so you must choose carefully. In addition, although pure cotton fabrics are comfortable, they have insufficient plasticity and elasticity, which is contrary to the concept of sports BRA. Relatively speaking, cotton blended Lycra is a good choice.


 

    2. Underwear elasticity is very important


    The degree of activity of each part of the body increases during fitness, so underwear must have better elasticity. In addition, better supporting performance is also an element to avoid excessive breast tremors when the body rises and falls.



    3. The size should be fit and the shoulder strap should be fixed


    Tights are generally worn during fitness, and the design of underwear should highlight the natural curve of the human body, and the obvious outline of the underwear cannot be seen from the outside of the tights. At the same time, the shoulder straps of underwear should not slip off, so as not to bring you unnecessary trouble.


    If you have started sports BRA, think about whether it is suitable for you, you can also start from the following directions.



    4. Shoulder strap


    A very important function of the shoulder strap of the sports BRA is to provide enough support for the breasts. To judge the supporting force of the shoulder strap, you can grasp one end of the shoulder strap with one hand, and the middle of the cup connected to it with the other hand, pull it hard, and observe its elasticity. The less elastic the shoulder strap, the greater the support it can provide.



    5. Drawstring


    To judge whether the strap is suitable, you only need to put a finger under the strap between the double bra cups and pull it hard. If you can't pull the strap 2.5 cm away from your body, then it is a qualified size. If it exceeds 2.5 cm too much, it means that your sports BRA is a bit big.


    In addition, you can also straighten your hands and raise your head. If the strap moves up, it also means that your sports BRA is too large and you need to change to a smaller size.



    6. Cup


    The judging criteria for the cup is similar to that of the shoulder strap. The smaller the elasticity of the fabric on the edge of the cup, the better the support for the chest. No matter what style of china sports bra, the cup must cover the entire breast without overflow. If you can't fully envelop, then you may need to change to a sports BRA.

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more