Teach you to buy a crib from three aspects

Babies are the heart and soul of parents. They spend half of their time in bed every day. It is particularly important to buy a good quality baby bed.   


The baby crib must be comfortable, safe and convenient. If you can buy a baby bed with a reasonable design, not only can you avoid the danger of your baby falling, to ensure the baby's healthy growth, but also provide a lot of convenience for mothers. So, how to buy a baby bed?


1. Material At present, the main materials for baby cots on the market are: metal (mainly iron), plastic and wood. Although the metal material is the strongest, it has a poor texture, is cold and too hard, and is not suitable for babies. Plastic is easy to deform, so it is still ideal for wood, which is strong and not too hard. Second, the size The size of the height bed can be determined according to the size of the room, and the height can be adjusted. It is more suitable for the bed surface to be 65-75 cm above the ground. Although it is a little higher, it is convenient to take care of, but it is not safe.


2. Security 1) There should be railings around the small bed, which can be pulled up and down, and fixed by bolts. The spacing between the railings of the bed is preferably about 11 cm. Too wide may make the baby slide down from the gap of the railing, and too narrow may cause inconvenience to the nursing operation. The height of the railing should be 50 cm above the mattress, if it is too low. Once a baby learns to grasp the railing and stand, there is a danger of falling out of the railing at any time; if it is too high, the mother will feel very tired when picking up or laying down the child. 2) The four corners of the bed should be round and smooth, so as to avoid sharp corners hanging on the baby's clothing and causing harm to the baby. 3) If the bed is assembled, pay special attention to whether the screws are tightened and the location of the bolts is safe.                 

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more