How to clean silicone earphone case

Silicone earphone case is commonly used accessories for earphone electronic products, which can protect the earphones from dust, shock, and drop to extend the life of the earphones. How to clean during daily use is also very important. Next, we will tell you some cleaning methods.


method 1

In the case that the silicone earphone cover will be stained with a small amount of dust after going out, you can simply rinse with clean water to remove the dust.


Method 2

When the silicone earphone sleeve is stained with hard-to-remove stains, such as lipstick, paintbrush, etc., it can be soaked in warm water for a while, and then wiped with a rag.


Method 3

If it is stained with oily substances such as credit oil, industrial oil, etc., you can soak it in hot water for a while. The soaking time is determined by observing the volatilization of the oil stain, and then remove some degreasing substances such as detergent. Carry out the operation to assist degreasing!


Method 4

When the silicone earphone sleeve is accidentally stained with paint, correction fluid and other things that are difficult to remove, you need to add the corresponding objects, and then take the old toothbrush to wash the silicone earphone sleeve.


Method 5

After long-term use, if you are worried about the growth of bacteria, you can wash it with boiling water or even directly put it in the sterilizer for a short while! But be careful of burns


The silicone earphone cover is made of silicone raw materials, because you must not touch the open flame when cleaning and using it, be careful of being melted, and also need to stay away from sharp and sharp objects to avoid damage caused by cutting! And after the cleaning work is completed, it needs to be dried in the sun before use to prevent bacteria from breeding at this time!


Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more