Cargo handover procedures in automobile cargo transportation

Cargo handover procedures in automobile cargo transportation


(1) Delivery and receipt of packaged goods by the contracting parties: In principle, bulk goods must be paid in pounds; heavy "door-to-door" containers, containers and other sealed goods must be delivered with lead seals.


(2) The shipper shall deliver the goods according to the agreed loading and unloading procedures; when loading the goods, both parties shall check the name, specification, and quantity of the goods on the spot, and check whether the packaging meets the prescribed standards or requirements. After the carrier confirms that it is correct, it shall Sign the shipper's delivery note; if it is found to be inconsistent with the regulations or endangering the safety of transportation, it is not allowed to ship; if the package is slightly damaged and it is difficult to repair and exchange in a short time, the shipper insists on loading and starting the shipment. Shipment can only be carried out after the record, signature and seal, and the shipper is responsible for the consequences.


(3) After the goods are delivered to the designated place, the consignee and the carrier shall hand over the goods on the spot, and the consignee shall sign the freight settlement voucher held by the carrier after the inspection is correct; if the goods are found to be damaged or poor, the transfer personnel of both parties shall make a record And signed, after the two parties jointly ascertain the situation and clarify the responsibilities, the consignee shall make a clear note on the freight voucher; the consignee shall not refuse to accept the goods due to damage to the goods.


(4) When the cargo is handed over, if both parties have doubts about the weight and content of the cargo, they can submit an inspection and rebalancing. If there is any discrepancy, they will be dealt with in accordance with relevant regulations; the responsible party shall bear the costs of inspection and rebalancing.


(5) The carrier shall deal with the goods that have not been picked up for more than 30 days from the next day after the receipt notice occurs:

①Establish a ledger, register it in time, keep it properly, not use it during storage, and carefully find the owner.

②After inquiries by multiple parties, the goods that have not been picked up for more than one month shall be handled in accordance with the "Measures on the Handling of Goods Unable to Deliver at Ports and Stations" by the State Economic Commission; but the fresh and difficult to keep goods are not subject to time restrictions upon approval by the competent department of the enterprise.

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more