Five tips for applying mask

Skin facial mask is an indispensable skin care product in daily maintenance. It can inject moisture and nutrients into the skin and make the skin look more hydrated and shiny. However, there are also skills in applying a mask. Use the right method to ensure that it doubles its effect!

Today I will tell you how to apply a mask to make the mask more effective!


First, wash your face.

The first thing to note is that you must wash your face before applying the mask. After cleansing, the skin can better absorb the nutrients in the mask. Otherwise, the sweat, grease, and dirt on the face will block the pores and cause acne.


Second, take a toner.

Secondly, we cannot apply a mask immediately after washing our face, because the skin after washing our face is in a dry state, and applying the mask directly will irritate the skin. Therefore, we can pat the toner first, make the skin moist, and then apply the mask, which can also promote the absorption of nutrients!


Third, massage the face after applying it.

After applying the mask, let's not worry about washing our face, first massage the face to promote blood circulation, so that the essence can be better absorbed, the effect is better!


Fourth, apply while lying down.

You must lie down when applying the mask! If you apply the mask while standing, sitting, or walking, your skin is prone to sagging or aging. So, just lie down and enjoy 15 minutes while applying the mask!


Fifth, apply a mask after taking a shower.

The last trick is to apply a mask after taking a shower. At this time, our skin pores are in an open state, which makes it easier to absorb the nutrients and moisture in the mask. However, remember to pat the toner before applying the mask~


These are the five tips for applying facial masks that I shared with you today. I hope it will be helpful to you all.

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more