Reasonable use method of ice cream display showcase

1. The ice cream is stored in the ice cream display showcase during the day, the temperature is between -16 ~ -19 degrees. The internal setting of the ice cream display showcase is set to automatically defrost every 6 hours, 6 minutes each time. When the machine is performing automatic defrosting, the temperature will rise to -5~-8, which is normal.


2. Ice cream should be moved to a refrigerator (or freezer) for storage at night, (it is recommended to shut down the ice cream display showcase at night for five to seven days), the temperature is at least: -18~-20 degrees, the temperature is -25 degrees is the best situation.


3. The refrigerator (or freezer) storing ice cream should be defrosted in real time, once or twice a week.


4. Since the ice cream is relatively hard just after being taken out from the freezer, it is recommended to open the ice cream display showcase in the morning and wait for the temperature of the display showcase to reach -10 degrees, and then quickly transfer the ice cream from the freezer to the display showcase. Later, you can try the softness and hardness of the ice cream by eating a spoon. After about half an hour, the ice cream will reach the softness and hardness. The temperature of the display showcase is automatically set to -16~-19, such as the extreme temperature caused by the outdoor temperature. When rising, you can manually adjust the temperature.


5. When storing ice cream at night, it should be covered with plastic wrap. If the plastic wrap has water drops, it should be replaced immediately, because the water drops will contact the ice cream and cause ice cream to appear, which seriously affects the taste of ice cream.


6. If the fruit on the fruit ice cream is not fresh, it should be replaced in time, if not, it will cause customers to think that the ice cream is not fresh. Decorations including some milk ice cream should be replaced immediately if they are not fresh.


7. The ice cream ball should be played forward from the last part of the ice cream tray. When the rear part is dug from top to bottom, then move forward. This will not damage the ice cream decorated in front, nor affect its aesthetics. In addition, when digging ice cream balls, by the way, dig out all the residues on the side of the plate, and dig while cleaning, so that it will not cause too much residue in the plate and affect the vision.


8. Check the ice cream at all times to keep the ice cream fresh and most attractive to customers. It is found that there is a place where the surface melts away; the oxide layer; use an ice cream spoon to scrape off. Check and wipe the stains on the display showcase at any time to make the window of the ice cream display showcase bright and clean.


9. All movements of ice cream at room temperature must be fast. Avoid letting ice cream contact room temperature, because this will cause the ice cream to melt, and then freeze to form ice crystals, which will affect the taste.


10. Every time you play a ball, you need to wash the ball player, so that it will not affect the color and taste of the next taste. And shake the water stains on the ball player to avoid the water stains forming ice crystals on the ice cream. Close the ice cream display showcase immediately after playing the ball to prevent hot air from entering the display showcase.


11. The freshness of the ice cream is within two weeks (the two weeks refer to the two weeks from the day when a new plate of ice cream stored in the freezer is placed in the display showcase). It is recommended that ice cream can be delivered in a promotional form within 10 or 15 days, such as buy one get one free. Don't smash the brand because it saves a little cost.


12. If the existing ice cream type is not enough to cover the ice cream display showcase, it should be filled with a clean empty plate, if not, it will affect the temperature of the display showcase.


13. The ice cream in the ice cream display showcase should be placed in different colors alternately, because the bright contrasting colors will attract customers' attention more.

Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more