How to Paint Ion Alloy Wheels

Painting of wheels transforms them into what you want them to look like. You can choose any color depending on the color of your car or your preference. When choosing primer, use a corrosive inhibitive primer to prevent shedding. Ensure the paint is durable to avoid fast fading, flaking, peeling and chipping. You will need the following things:

Detergent and water

Scouring pad and Mask

Painters tape and a Moon-shaped cardboard

Trisodiumphosphate

Towel

120-320, 600, and the 1000-1500 grit sand papers

Primer

Color paint and Clear paint

1. You can paint the wheels while removed from the car or not. Clean the Ion Alloy Wheel thoroughly to remove dirt and grime. The paint is most likely not going to hold if the wheel is dirty. Clean the wheel thoroughly with soap or detergent, a scouring pad and water. Use Trisodium Phosphate to remove any grease and oil that wasn't taken out by the first clean. Dry the wheel thoroughly with a towel.

2. After cleaning the wheels, use the 120-320 grit sand paper to remove the current finish. This will also help the undercoat (primer) stick to the wheels when applied. Ion Alloy Wheels are made of chrome hence you have to make sure you get below the chrome surface when sanding. Sanding ensures that all flaking, oxidation, dust and dirt are removed. Sand the wheels again using a 600 grit sandpaper to make sure small bumps, debris and flaws are removed.

3. If the wheels are not removed, cover the tires with painters tape and plastic sheeting. Put the tape around the rim's edges and on the side walls to protect the tire from getting paint. Using the moon-shaped (half-moon preferably) cut cardboard to protect the paint from the spray by placing it at an angle between the wheel and the wheel well.

4. Put on a mask to avoid inhaling the paint and start the primer. Ensure the working area is dust free to avoid dust catching on the wet paint. Spraying 2 to 3 coats of the primer will do on the wheel. After it dries up, sand it lightly using the 600 grit sand paper.

5. The Ion Alloy Wheels are then sprayed with 2 to 3 coats of color paint. Avoid runs and imperfections to avoid repeating the process the following day. If you decide to use rubbing compound on paint, make sure any remaining compound is washed off before you apply the clear coat. Satisfied the paint looks good, spray the clear coat on.

6. Spray the Ion Alloy Wheels with 2 to 3 coats of clear coat and leave it overnight to dry. Remove rough edges and imperfections using the 1000 to 1500 grit sand paper. To make sure the shine on the wheel is back, use the fine rubbing compound. The Carbona Wax is then applied to ensure more protection and shine.

After painting, give the paint time to dry before driving your car. Spray in an open space for ventilation purposes. Always have extra paint to touch when necessary. Protect your wheels from scratches when removing them or changing tires. Your wheels after drying are an incredible sight to look at.


Comments

Post a Comment

Popular posts from this blog

How to Hang a Suspended Ceiling From Steel Beams

The suspended ceiling hangs under the roof or floor structure above, hiding ugly mechanical and electrical equipment from the view, while also allowing you to easily reach these equipment as needed.While wooden frames usually support such ceilings, in rooms where metal frames are used instead of traditional wood, you can also hang ceilings from steel beams.Hanging the ceiling from the beam requires you to use a special clip to connect the support line to the beam without compromising its structural integrity.Measure 4 inch down from the bottom of the lowest beam, pipe or pipe in the ceiling space.If you plan to use panel fluorescent lamps in your ceiling, add an additional 2 inch to this measurement.Make a mark on the wall indicating the location of the facade.Set up a laser level to extend the mark you made on the wall to the entire wall length.Draw a chalk line on the wall to mark the position.Mark all four walls repeatedly with chalk lines indicating the height of the ceiling.Instal
Read more

Importance of Calibration Service, Material Testing

When it comes to Calibration services, genuine service providers offer full recall system and data sheets for all items calibrated. Service needs to be instrument specific. With the advent of technology, Calibration service has seen a tremendous change and has gone through various phases to get the top quality. Calibration is a great deal for industrial purpose. It makes sure that products are manufactured as per specification. It also checks the competence level of technically valid results. The calibrated measuring instrument helps in checking the quality and valuation of the product. In cases of electronic equipment, it is essential to calibrate instruments to keep a check on quality and performance. Calibration facilitates in improving measurement abilities. Calibration service can be manual or automated.  textile testing equipment manufacturers Material Testing machines are available for a wide variety of industries including materials testers for plastics, textiles, adhesives, fi
Read more

Level Measurement Solutions

Makeup water treatment is an important component of steam generation. It is the means to resupply the system with water suitable for boiler and other operations that, was lost in the cycle.The steam generation cycle, level control for the water treatment process is not necessarily about efficiency, but rather, accuracy, reliability and safety, while providing proper inventory management to ensure chemical and makeup water supply meets demand. The focus is on the chemical component of the makeup water treatment since it presents difficulties for level technologies that may work perfectly on non-chemical applications related to the water treatment process or those with limited variations in the contents of the vessel's vapor space. Although important measurements such as ammonia, acid, caustic and other chemical storage tanks are not difficult level applications by any stretch, small nuances in how the vessels are monitored relative to level technology can have a dramatic effect on t
Read more